ET01 and ET02 - (25001 Products)
5/8 x 3-1/2 x 24 - 498 Low Carbon Precision Ground Flat Stock
Item #: LY8055009
Manufacturer: Starrett
Mfg #: 55009
Technical Specifications:
*Brand Name: Starrett
*Length: 24
*Material: LC
*Thick: 5/8
*Width: 3-1/2
Description:
*Substantial cost reductions over tool steel ground flat stock. There are savings up to 60% because this is a low carbon steel and furnished in 24" lengths. This means that you get one-third more steel at less cost
* Ideal for a wide variety of parts that don't require more expensive heat treated steels, such as stripper plates, jigs, fixtures, machine and component parts, templates, etc.
*This steel can be carburized or case hardened. After hardening, its physical properties, especially tensile strength, yield point, and Brinell hardness, are substantially higher.
*Furnished in 24" (610mm) lengths, ground straight and parallel
Shipping Info:
*Actual Weight - 14.8700
5/16 x 7/8 x 36 - A6 Air Hardening Precision Ground Flat Stock
Item #: LY4459015
Manufacturer: Starrett
Mfg #: 59015
Technical Specifications:
*Brand Name: Starrett
*Length: 36
*Material: A-6
*Thick: 5/16
*Width: 7/8
Description:
*344 A6 air hardening flat stock is a medium alloyed air hardening tool steel that provides an excellent balance of machinability, toughness and wear resistance
*Lower heat treating temperature results in deep hardness and minimum distortion
Shipping Info:
*Actual Weight - 2.7900
36 x 3/16 x 4 - Oversize Air Hardening Flat Stock
Item #: LY4656902
Manufacturer: Starrett
Mfg #: 56902
Technical Specifications:
*Brand Name: Starrett
*Length: 36
*Material: A-2
*Thick: 3/16
*Width: 4
Description:
*Oversize A-2 Air Hardening Ground Flat Stock
Shipping Info:
*Actual Weight - 8.2700
18 x 3/16 x 10 - Oil Hardening Flat Stock
Item #: LY4054057
Manufacturer: Starrett
Mfg #: 54057
Technical Specifications:
*Brand Name: Starrett
*Length: 18
*Material: O-1
*Thick: 3/16
*Width: 10
Description:
*Precision Ground 0-1 Gage Stock 18" Length
*0-1 Oil Hardening Ground Flat Stock
*Electric furnace melt oil-hardening tool steel supplied with a fully spheroidized structure
*Non-shrinking general purpose tool steel
*HEAT TREATMENT: For sections smaller than 1/4" heat to 1450?_1475?F& hold until heated through. For larger sections, preheat to 1200?F, then raise to 1450?_1500?F hardening temperature, hold half an hour per inch of cross section. Quench in oil at 125?_150?F & Temper Immediately.
*Tolerance Thickness ±.001" Width +.000 / .005"
Shipping Info:
*Actual Weight - 9.6600
3/16 x 6 x 24 - 498 Low Carbon Precision Ground Flat Stock
Item #: LY8054932
Manufacturer: Starrett
Mfg #: 54932
Technical Specifications:
*Brand Name: Starrett
*Length: 24
*Material: LC
*Thick: 3/16
*Width: 6
Description:
*Substantial cost reductions over tool steel ground flat stock. There are savings up to 60% because this is a low carbon steel and furnished in 24" lengths. This means that you get one-third more steel at less cost
* Ideal for a wide variety of parts that don't require more expensive heat treated steels, such as stripper plates, jigs, fixtures, machine and component parts, templates, etc.
*This steel can be carburized or case hardened. After hardening, its physical properties, especially tensile strength, yield point, and Brinell hardness, are substantially higher.
*Furnished in 24" (610mm) lengths, ground straight and parallel
Shipping Info:
*Actual Weight - 7.6500
36 x 1-1/4 x 2 - Oil Hardening Flat Stock
Item #: LY5111603
Manufacturer: Generic USA
Mfg #:
Technical Specifications:
*Brand Name: Generic USA
*Length: 36
*Material: O-1
*Thick: 1-1/4
*Width: 2
Description:
*Precision Ground 0-1 Gage Stock 36" Length
*O-1 Oil Hardening Ground Flat Stock
*Electric furnace melt oil-hardening tool steel supplied with a fully spheroidized structure
*Non-shrinking general purpose tool steel
*HEAT TREATMENT: For sections smaller than 1/4" heat to 1450? _ 1475?F& hold until heated through. For larger sections, preheat to 1200?F, then raise to 1450? _ 1500?F hardening temperature, hold half an hour per inch of cross section. Quench in oil at 125? _1 50?F & Temper Immediately.
*Tolerance Thickness ±.001" Width +.000 / .005"
Shipping Info:
*Actual Weight - 25.6100
36 x 1/4 x 4 - Oversize Oil Hardening Flat Stock
Item #: LY4156832
Manufacturer: Starrett
Mfg #: 56832
Technical Specifications:
*Brand Name: Starrett
*Length: 36
*Material: O-1
*Thick: 1/4
*Width: 4
Description:
*Oversize 0-1 Oil Hardening Ground Flat Stock
*Flat Ground Stock is manufactured from fine grain tool steel, electrically melted from high grade materials to close limits of analysis
*Ideal for the manufacture of dies, gages, punches, templates, jigs and precision tools
*Width +.010/.015
*Thickness +10.010/.015
*Squareness edge to surface .003 per inch of thickness
*Finish 10-25 micro inches
Shipping Info:
*Actual Weight - 10.8500
3/16 x 6 x 18 - Oversize High Carbon, High Chromium Precision Ground Flat Stock
Item #: LY4369399
Manufacturer: Starrett
Mfg #: 69399
Technical Specifications:
*Brand Name: Starrett
*Length: 18
*Material: D-2
*Thick: 3/16
*Width: 6
Description:
*401 is (AISI D2) high chromium steel for the highest wear resistance applications
*Standard size: +/-.001" thickness tolerance
*High carbon, high chromium steel
*For applications that demand the highest wear resistance 401 is standard tolerance
*Ground straight and parallel
Shipping Info:
*Actual Weight - 5.7400
9/16 x 3 x 18 - Oversize Air Hardening Flat Stock
Item #: LY4657617
Manufacturer: Starrett
Mfg #: 57617
Technical Specifications:
*Brand Name: Starrett
*Length: 18
*Material: A-2
*Thick: 9/16
*Width: 3
Description:
*499 s a A-2 5% chromium air hardening steel with high wear and abrasion resistance
*Oversize: +.010"/.015" thickness tolerance
*Maintains close dimensional accuracy throughout the heat treating process
*The 5% chromium content makes this steel especially desirable for punches and dies to be used in long production runs since it gives the tools far longer life.
*Up to 50% more pieces per sharpening can be produced than with oil hardening steel
*High wear resistance is also ideal for punches and dies to stamp silicon, stainless steels, monel metal and other types of abrasive material
*Maintains close dimensional accuracy throughout the heat treating process. The wide 75? hardening range make this virtually foolproof
*Full-length identification eliminates confusion with other steels
*Furnished in 18" and 36" lengths, ground straight and parallel
Shipping Info:
*Actual Weight - 8.6100
1/2 x 3 x 18 - High Carbon, High Chromium Precision Ground Flat Stock
Item #: LY4269191
Manufacturer: Starrett
Mfg #: 69191
Technical Specifications:
*Brand Name: Starrett
*Length: 18
*Material: D-2
*Thick: 1/2
*Width: 3
Description:
*401 is (AISI D2) high chromium steel for the highest wear resistance applications
*Standard size: +/-.001" thickness tolerance
*High carbon, high chromium steel
*For applications that demand the highest wear resistance 401 is standard tolerance
*Ground straight and parallel
Shipping Info:
*Actual Weight - 7.6500
1/2X10X24 CARBON FLAT STOCK
Item #: LY8002200
Manufacturer: Generic USA
Mfg #:
Technical Specifications:
*Brand Name: Generic USA
Description:
Shipping Info:
*Actual Weight - 34.4000
36 x 7/8 x 3 - Oil Hardening Flat Stock
Item #: LY5105607
Manufacturer: Generic USA
Mfg #:
Technical Specifications:
*Brand Name: Generic USA
*Length: 36
*Material: O-1
*Thick: 7/8
*Width: 3
Description:
*Precision Ground 0-1 Gage Stock 36" Length
*O-1 Oil Hardening Ground Flat Stock
*Electric furnace melt oil-hardening tool steel supplied with a fully spheroidized structure
*Non-shrinking general purpose tool steel
*HEAT TREATMENT: For sections smaller than 1/4" heat to 1450? _ 1475?F& hold until heated through. For larger sections, preheat to 1200?F, then raise to 1450? _ 1500?F hardening temperature, hold half an hour per inch of cross section. Quench in oil at 125? _1 50?F & Temper Immediately.
*Tolerance Thickness ±.001" Width +.000 / .005"
Shipping Info:
*Actual Weight - 27.0500
36 x 1/2 x 2 - Oversize Oil Hardening Flat Stock
Item #: LY4156863
Manufacturer: Starrett
Mfg #: 56863
Technical Specifications:
*Brand Name: Starrett
*Length: 36
*Material: O-1
*Thick: 1/2
*Width: 2
Description:
*Oversize 0-1 Oil Hardening Ground Flat Stock
*Flat Ground Stock is manufactured from fine grain tool steel, electrically melted from high grade materials to close limits of analysis
*Ideal for the manufacture of dies, gages, punches, templates, jigs and precision tools
*Width +.010/.015
*Thickness +10.010/.015
*Squareness edge to surface .003 per inch of thickness
*Finish 10-25 micro inches
Shipping Info:
*Actual Weight - 10.6300
7/8 x 2 x 18 - Oversize Air Hardening Flat Stock
Item #: LY4657639
Manufacturer: Starrett
Mfg #: 57639
Technical Specifications:
*Brand Name: Starrett
*Length: 18
*Material: A-2
*Thick: 7/8
*Width: 2
Description:
*499 s a A-2 5% chromium air hardening steel with high wear and abrasion resistance
*Oversize: +.010"/.015" thickness tolerance
*Maintains close dimensional accuracy throughout the heat treating process
*The 5% chromium content makes this steel especially desirable for punches and dies to be used in long production runs since it gives the tools far longer life.
*Up to 50% more pieces per sharpening can be produced than with oil hardening steel
*High wear resistance is also ideal for punches and dies to stamp silicon, stainless steels, monel metal and other types of abrasive material
*Maintains close dimensional accuracy throughout the heat treating process. The wide 75? hardening range make this virtually foolproof
*Full-length identification eliminates confusion with other steels
*Furnished in 18" and 36" lengths, ground straight and parallel
Shipping Info:
*Actual Weight - 8.9200
36 x 1 x 1-1/4 - Oil Hardening Flat Stock
Item #: LY4054501
Manufacturer: Starrett
Mfg #: 54501
Technical Specifications:
*Brand Name: Starrett
*Length: 36
*Material: O-1
*Thick: 1
*Width: 1-1/4
Description:
*Precision Ground 0-1 Gage Stock 36" Length
*O-1 Oil Hardening Ground Flat Stock
*Electric furnace melt oil-hardening tool steel supplied with a fully spheroidized structure
*Non-shrinking general purpose tool steel
*HEAT TREATMENT: For sections smaller than 1/4" heat to 1450? _ 1475?F& hold until heated through. For larger sections, preheat to 1200?F, then raise to 1450? _ 1500?F hardening temperature, hold half an hour per inch of cross section. Quench in oil at 125? _1 50?F & Temper Immediately.
*Tolerance Thickness ±.001" Width +.000 / .005"
Shipping Info:
*Actual Weight - 12.9100
36 x 7/16 x 3 - Oil Hardening Flat Stock
Item #: LY4054434
Manufacturer: Starrett
Mfg #: 54434
Technical Specifications:
*Brand Name: Starrett
*Length: 36
*Material: O-1
*Thick: 7/16
*Width: 3
Description:
*Precision Ground 0-1 Gage Stock 36" Length
*O-1 Oil Hardening Ground Flat Stock
*Electric furnace melt oil-hardening tool steel supplied with a fully spheroidized structure
*Non-shrinking general purpose tool steel
*HEAT TREATMENT: For sections smaller than 1/4" heat to 1450? _ 1475?F& hold until heated through. For larger sections, preheat to 1200?F, then raise to 1450? _ 1500?F hardening temperature, hold half an hour per inch of cross section. Quench in oil at 125? _1 50?F & Temper Immediately.
*Tolerance Thickness ±.001" Width +.000 / .005"
Shipping Info:
*Actual Weight - 13.5400
3/16 x 1-3/4 x 36 - A6 Air Hardening Precision Ground Flat Stock
Item #: LY4458976
Manufacturer: Starrett
Mfg #: 58976
Technical Specifications:
*Brand Name: Starrett
*Length: 36
*Material: A-6
*Thick: 3/16
*Width: 1-3/4
Description:
*344 A6 air hardening flat stock is a medium alloyed air hardening tool steel that provides an excellent balance of machinability, toughness and wear resistance
*Lower heat treating temperature results in deep hardness and minimum distortion
Shipping Info:
*Actual Weight - 3.3500
36 x 3/16 x 4 - Air Hardening Flat Stock
Item #: LY4554574
Manufacturer: Starrett
Mfg #: 54574
Technical Specifications:
*Brand Name: Starrett
*Length: 36
*Material: A-2
*Thick: 3/16
*Width: 4
Description:
*A-2 Air Hardening Ground Flat Stock 36" Length
*Made from fine grain, electric furnace air-hardening, 5 chrome tool steel
*Has excellent wear and abrasion resistance properties
*Furnished with a fully spheroidized structure and is 100 free of decarb and other surface imperfections.
*Low sulphur content makes it non-freemachining.
*HEAT TREATMENT: Preheat thoroughly at 1450?F, then raise to hardening temperature 1725? _ 1800?F and soak uniformly. For larger sections, use high side; for thin or smaller sections, use low side. Quench in still air or dry air blast at 125? _ 175?F, then Temper Immediately.
*Tolerance Thickness ±.001" Width +.000/.005"
*Larger Sizes A-2 available thru 1" thickness
*Oversize tolerances available thru 2" thickness
*Many other types of gage stock available
*Modified Nutec 42
*A-6 Diecrat
*D-2 Aristocrat
*S-7
*C-1018 Marshallcrat low carbon
Shipping Info:
*Actual Weight - 7.7300
1/2 x 1-1/4 x 36 - Oversize High Carbon, High Chromium Precision Ground Flat Stock
Item #: LY4369550
Manufacturer: Starrett
Mfg #: 69550
Technical Specifications:
*Brand Name: Starrett
*Length: 36
*Material: D-2
*Thick: 1/2
*Width: 1-1/4
Description:
*401 is (AISI D2) high chromium steel for the highest wear resistance applications
*Standard size: +/-.001" thickness tolerance
*High carbon, high chromium steel
*For applications that demand the highest wear resistance 401 is standard tolerance
*Ground straight and parallel
Shipping Info:
*Actual Weight - 6.3700
36 x 5/32 x 6 - Oil Hardening Flat Stock
Item #: LY4054336
Manufacturer: Starrett
Mfg #: 54336
Technical Specifications:
*Brand Name: Starrett
*Length: 36
*Material: O-1
*Thick: 5/32
*Width: 6
Description:
*Precision Ground 0-1 Gage Stock 36" Length
*O-1 Oil Hardening Ground Flat Stock
*Electric furnace melt oil-hardening tool steel supplied with a fully spheroidized structure
*Non-shrinking general purpose tool steel
*HEAT TREATMENT: For sections smaller than 1/4" heat to 1450? _ 1475?F& hold until heated through. For larger sections, preheat to 1200?F, then raise to 1450? _ 1500?F hardening temperature, hold half an hour per inch of cross section. Quench in oil at 125? _1 50?F & Temper Immediately.
*Tolerance Thickness ±.001" Width +.000 / .005"
Shipping Info:
*Actual Weight - 9.6700