ET01 and ET02 - (25001 Products)
HSK-E40 3/8" Bore Dia. x 3.15 Gage Length Shrink Fit Toolholder
Item #: GM269079215
Manufacturer: Bilz
Mfg #: 9079215
Technical Specifications:
*Bearing Surface: 1.65
*Bore Diameter: 3/8"
*Brand Name: Bilz
*Gage Length: 3.15
*Outside Diameter: 1.26
*Shank: HSK-E40
*Type: Shrink Fit Toolholder
Description:
Shipping Info:
*Actual Weight - 1.3000
BT40 7/8 x 3.54 - Shrink Fit Tool Holder
Item #: GM94BT40883549
Manufacturer: Parlec
Mfg #: BT40-88SF3
Technical Specifications:
*Bore Diameter: 7/8
*Brand Name: Parlec
*Gage Length: 3.540
*Model Number: BT40-88SF354-9
*Shank: BT40
*Standard: DIN
Description:
*Shrink Fit Tool Holder
*Improved concentricity
*Improved balance design with no moving pieces
*Low Centrifugal Forces due to low holder mass
*For maximum gripping power with exceptional concentricity
*Concentricity of .0001" with tool shrunk in holder
*Chip load distributed evenly along cutting edge of tool which results in longer tool life
*Constructed of double tempered Tool Steel for exceptional durability and cycle life
*With proper use, toolholder life should exceed that of standard end mill holders
*Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force
*Short projections are possible because no mechanical clamping devices are used
*This results in greater rigidity and resistance to bending
*Simple and fast to use
*The total time elapsed to remove one cutting tool and insert another is less than 10 seconds
*Through-spindle coolant capability
*Coolant through holders require no special backup screws or seals
*The interference fit between the ID of the tool holder and cutting tool shank forms the seal, preventing the coolant from flowing anywhere else except through the coolant grooves
*The use of Heat Shrink Tooling allows for greater speeds and feeds, better finishes, increased tool life, and increased productivity due to its High Speed Machining capability and simplicity of use
Shipping Info:
*Actual Weight - 3.0000
CAT40 1-1/4 x 3.94 - Shrink Fit Tool Holder
Item #: GM94C40123949
Manufacturer: Parlec
Mfg #: C40-12SF39
Technical Specifications:
*Bore Diameter: 1-1/4
*Brand Name: Parlec
*Gage Length: 3.940
*Model Number: C40-12SF394-9
*Shank: CAT40
*Standard: DIN
Description:
*Shrink Fit Tool Holder
*Improved concentricity
*Improved balance design with no moving pieces
*Low Centrifugal Forces due to low holder mass
*For maximum gripping power with exceptional concentricity
*Concentricity of .0001" with tool shrunk in holder
*Chip load distributed evenly along cutting edge of tool which results in longer tool life
*Constructed of double tempered Tool Steel for exceptional durability and cycle life
*With proper use, toolholder life should exceed that of standard end mill holders
*Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force
*Short projections are possible because no mechanical clamping devices are used
*This results in greater rigidity and resistance to bending
*Simple and fast to use
*The total time elapsed to remove one cutting tool and insert another is less than 10 seconds
*Through-spindle coolant capability
*Coolant through holders require no special backup screws or seals
*The interference fit between the ID of the tool holder and cutting tool shank forms the seal, preventing the coolant from flowing anywhere else except through the coolant grooves
*The use of Heat Shrink Tooling allows for greater speeds and feeds, better finishes, increased tool life, and increased productivity due to its High Speed Machining capability and simplicity of use
Shipping Info:
*Actual Weight - 3.0000
CAT40 1 x 3.94 - Shrink Fit Tool Holder
Item #: GM94C40103949
Manufacturer: Parlec
Mfg #: C40-10SF39
Technical Specifications:
*Bore Diameter: 1
*Brand Name: Parlec
*Gage Length: 3.940
*Model Number: C40-10SF394-9
*Shank: CAT40
*Standard: DIN
Description:
*Shrink Fit Tool Holder
*Improved concentricity
*Improved balance design with no moving pieces
*Low Centrifugal Forces due to low holder mass
*For maximum gripping power with exceptional concentricity
*Concentricity of .0001" with tool shrunk in holder
*Chip load distributed evenly along cutting edge of tool which results in longer tool life
*Constructed of double tempered Tool Steel for exceptional durability and cycle life
*With proper use, toolholder life should exceed that of standard end mill holders
*Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force
*Short projections are possible because no mechanical clamping devices are used
*This results in greater rigidity and resistance to bending
*Simple and fast to use
*The total time elapsed to remove one cutting tool and insert another is less than 10 seconds
*Through-spindle coolant capability
*Coolant through holders require no special backup screws or seals
*The interference fit between the ID of the tool holder and cutting tool shank forms the seal, preventing the coolant from flowing anywhere else except through the coolant grooves
*The use of Heat Shrink Tooling allows for greater speeds and feeds, better finishes, increased tool life, and increased productivity due to its High Speed Machining capability and simplicity of use
Shipping Info:
*Actual Weight - 3.0000
CAT40 3/16 x 3.15 - Shrink Fit Tool Holder
Item #: GM94C40183159
Manufacturer: Parlec
Mfg #: C40-18SF31
Technical Specifications:
*Bore Diameter: 3/16
*Brand Name: Parlec
*Gage Length: 3.150
*Model Number: C40-18SF315-9
*Shank: CAT40
*Standard: DIN
Description:
*Shrink Fit Tool Holder
*Improved concentricity
*Improved balance design with no moving pieces
*Low Centrifugal Forces due to low holder mass
*For maximum gripping power with exceptional concentricity
*Concentricity of .0001" with tool shrunk in holder
*Chip load distributed evenly along cutting edge of tool which results in longer tool life
*Constructed of double tempered Tool Steel for exceptional durability and cycle life
*With proper use, toolholder life should exceed that of standard end mill holders
*Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force
*Short projections are possible because no mechanical clamping devices are used
*This results in greater rigidity and resistance to bending
*Simple and fast to use
*The total time elapsed to remove one cutting tool and insert another is less than 10 seconds
*Through-spindle coolant capability
*Coolant through holders require no special backup screws or seals
*The interference fit between the ID of the tool holder and cutting tool shank forms the seal, preventing the coolant from flowing anywhere else except through the coolant grooves
*The use of Heat Shrink Tooling allows for greater speeds and feeds, better finishes, increased tool life, and increased productivity due to its High Speed Machining capability and simplicity of use
Shipping Info:
*Actual Weight - 3.0000
CAT40 1/2 x 3.15 - Shrink Fit Tool Holder
Item #: GM94C40503159
Manufacturer: Parlec
Mfg #: C40-50SF31
Technical Specifications:
*Bore Diameter: 1/2
*Brand Name: Parlec
*Gage Length: 3.150
*Model Number: C40-50SF315-9
*Shank: CAT40
*Standard: DIN
Description:
*Shrink Fit Tool Holder
*Improved concentricity
*Improved balance design with no moving pieces
*Low Centrifugal Forces due to low holder mass
*For maximum gripping power with exceptional concentricity
*Concentricity of .0001" with tool shrunk in holder
*Chip load distributed evenly along cutting edge of tool which results in longer tool life
*Constructed of double tempered Tool Steel for exceptional durability and cycle life
*With proper use, toolholder life should exceed that of standard end mill holders
*Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force
*Short projections are possible because no mechanical clamping devices are used
*This results in greater rigidity and resistance to bending
*Simple and fast to use
*The total time elapsed to remove one cutting tool and insert another is less than 10 seconds
*Through-spindle coolant capability
*Coolant through holders require no special backup screws or seals
*The interference fit between the ID of the tool holder and cutting tool shank forms the seal, preventing the coolant from flowing anywhere else except through the coolant grooves
*The use of Heat Shrink Tooling allows for greater speeds and feeds, better finishes, increased tool life, and increased productivity due to its High Speed Machining capability and simplicity of use
Shipping Info:
*Actual Weight - 3.0000
CAT40 5/8 x 3.15 - Shrink Fit Tool Holder
Item #: GM94C40623159
Manufacturer: Parlec
Mfg #: C40-62SF31
Technical Specifications:
*Bore Diameter: 5/8
*Brand Name: Parlec
*Gage Length: 3.150
*Model Number: C40-62SF315-9
*Shank: CAT40
*Standard: DIN
Description:
*Shrink Fit Tool Holder
*Improved concentricity
*Improved balance design with no moving pieces
*Low Centrifugal Forces due to low holder mass
*For maximum gripping power with exceptional concentricity
*Concentricity of .0001" with tool shrunk in holder
*Chip load distributed evenly along cutting edge of tool which results in longer tool life
*Constructed of double tempered Tool Steel for exceptional durability and cycle life
*With proper use, toolholder life should exceed that of standard end mill holders
*Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force
*Short projections are possible because no mechanical clamping devices are used
*This results in greater rigidity and resistance to bending
*Simple and fast to use
*The total time elapsed to remove one cutting tool and insert another is less than 10 seconds
*Through-spindle coolant capability
*Coolant through holders require no special backup screws or seals
*The interference fit between the ID of the tool holder and cutting tool shank forms the seal, preventing the coolant from flowing anywhere else except through the coolant grooves
*The use of Heat Shrink Tooling allows for greater speeds and feeds, better finishes, increased tool life, and increased productivity due to its High Speed Machining capability and simplicity of use
Shipping Info:
*Actual Weight - 3.0000
CAT40 3/4 x 3.15 - Shrink Fit Tool Holder
Item #: GM94C40753159
Manufacturer: Parlec
Mfg #: C40-75SF31
Technical Specifications:
*Bore Diameter: 3/4
*Brand Name: Parlec
*Gage Length: 3.150
*Model Number: C40-75SF315-9
*Shank: CAT40
*Standard: DIN
Description:
*Shrink Fit Tool Holder
*Improved concentricity
*Improved balance design with no moving pieces
*Low Centrifugal Forces due to low holder mass
*For maximum gripping power with exceptional concentricity
*Concentricity of .0001" with tool shrunk in holder
*Chip load distributed evenly along cutting edge of tool which results in longer tool life
*Constructed of double tempered Tool Steel for exceptional durability and cycle life
*With proper use, toolholder life should exceed that of standard end mill holders
*Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force
*Short projections are possible because no mechanical clamping devices are used
*This results in greater rigidity and resistance to bending
*Simple and fast to use
*The total time elapsed to remove one cutting tool and insert another is less than 10 seconds
*Through-spindle coolant capability
*Coolant through holders require no special backup screws or seals
*The interference fit between the ID of the tool holder and cutting tool shank forms the seal, preventing the coolant from flowing anywhere else except through the coolant grooves
*The use of Heat Shrink Tooling allows for greater speeds and feeds, better finishes, increased tool life, and increased productivity due to its High Speed Machining capability and simplicity of use
Shipping Info:
*Actual Weight - 3.0000
CAT40 1/4 x 3.15 - Shrink Fit Tool Holder
Item #: GM94C40253159
Manufacturer: Parlec
Mfg #: C40-25SF31
Technical Specifications:
*Bore Diameter: 1/4
*Brand Name: Parlec
*Gage Length: 3.150
*Model Number: C40-25SF315-9
*Shank: CAT40
*Standard: DIN
Description:
*Shrink Fit Tool Holder
*Improved concentricity
*Improved balance design with no moving pieces
*Low Centrifugal Forces due to low holder mass
*For maximum gripping power with exceptional concentricity
*Concentricity of .0001" with tool shrunk in holder
*Chip load distributed evenly along cutting edge of tool which results in longer tool life
*Constructed of double tempered Tool Steel for exceptional durability and cycle life
*With proper use, toolholder life should exceed that of standard end mill holders
*Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force
*Short projections are possible because no mechanical clamping devices are used
*This results in greater rigidity and resistance to bending
*Simple and fast to use
*The total time elapsed to remove one cutting tool and insert another is less than 10 seconds
*Through-spindle coolant capability
*Coolant through holders require no special backup screws or seals
*The interference fit between the ID of the tool holder and cutting tool shank forms the seal, preventing the coolant from flowing anywhere else except through the coolant grooves
*The use of Heat Shrink Tooling allows for greater speeds and feeds, better finishes, increased tool life, and increased productivity due to its High Speed Machining capability and simplicity of use
Shipping Info:
*Actual Weight - 2.3000
*Dimensions - Height: 2.80 Length: 7.40 Width: 2.80
CAT40 3/8 x 3.15 - Shrink Fit Tool Holder
Item #: GM94C40383159
Manufacturer: Parlec
Mfg #: C40-38SF31
Technical Specifications:
*Bore Diameter: 3/8
*Brand Name: Parlec
*Gage Length: 3.150
*Model Number: C40-38SF315-9
*Shank: CAT40
*Standard: DIN
Description:
*Shrink Fit Tool Holder
*Improved concentricity
*Improved balance design with no moving pieces
*Low Centrifugal Forces due to low holder mass
*For maximum gripping power with exceptional concentricity
*Concentricity of .0001" with tool shrunk in holder
*Chip load distributed evenly along cutting edge of tool which results in longer tool life
*Constructed of double tempered Tool Steel for exceptional durability and cycle life
*With proper use, toolholder life should exceed that of standard end mill holders
*Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force
*Short projections are possible because no mechanical clamping devices are used
*This results in greater rigidity and resistance to bending
*Simple and fast to use
*The total time elapsed to remove one cutting tool and insert another is less than 10 seconds
*Through-spindle coolant capability
*Coolant through holders require no special backup screws or seals
*The interference fit between the ID of the tool holder and cutting tool shank forms the seal, preventing the coolant from flowing anywhere else except through the coolant grooves
*The use of Heat Shrink Tooling allows for greater speeds and feeds, better finishes, increased tool life, and increased productivity due to its High Speed Machining capability and simplicity of use
Shipping Info:
*Actual Weight - 3.0000
CAT40 5/16 x 3.15 - Shrink Fit Tool Holder
Item #: GM94C40313159
Manufacturer: Parlec
Mfg #: C40-31SF31
Technical Specifications:
*Bore Diameter: 5/16
*Brand Name: Parlec
*Gage Length: 3.150
*Model Number: C40-31SF315-9
*Shank: CAT40
*Standard: DIN
Description:
*Shrink Fit Tool Holder
*Improved concentricity
*Improved balance design with no moving pieces
*Low Centrifugal Forces due to low holder mass
*For maximum gripping power with exceptional concentricity
*Concentricity of .0001" with tool shrunk in holder
*Chip load distributed evenly along cutting edge of tool which results in longer tool life
*Constructed of double tempered Tool Steel for exceptional durability and cycle life
*With proper use, toolholder life should exceed that of standard end mill holders
*Tool is gripped 360° along the entire length of bore resulting in an evenly distributed clamping force
*Short projections are possible because no mechanical clamping devices are used
*This results in greater rigidity and resistance to bending
*Simple and fast to use
*The total time elapsed to remove one cutting tool and insert another is less than 10 seconds
*Through-spindle coolant capability
*Coolant through holders require no special backup screws or seals
*The interference fit between the ID of the tool holder and cutting tool shank forms the seal, preventing the coolant from flowing anywhere else except through the coolant grooves
*The use of Heat Shrink Tooling allows for greater speeds and feeds, better finishes, increased tool life, and increased productivity due to its High Speed Machining capability and simplicity of use
Shipping Info:
*Actual Weight - 3.0000
ST19.05-SLS1/4-110
Item #: TP349910138
Manufacturer: OSG USA, Inc.
Mfg #: 9910138
Technical Specifications:
*Brand Name: OSG USA, Inc.
*List No.: SHRINK
Description:
Shipping Info:
*Actual Weight - .3900
*Dimensions - Height: 1.20 Length: 4.45 Width: 1.30
CAT40 3/4"-4" - Shrink Fit Holder with Coolblast
Item #: TE1229036B
Manufacturer: Techniks
Mfg #: 29036B
Technical Specifications:
*Bore Diameter: 3/4
*Brand Name: Techniks
*European-DIN Tool Shank Range: 19.1mm
*Gage Length: 4
*Outside Diameter: 2.5
*Shank: 3/4
*Standard: ISO 1940
*Type: Shrink Fit CAT Holder
*USA-ANSI Tool Shank Range: 3/4
Description:
*ShrinkFIT tooling improves cutting tool life, cutting ability, and surface finish
*ShrinkFIT produces less wear and tear on the spindle bearings
*CoolBLAST allows for in-the-bore coolant delivery onto the work piece
*Ideal for high-speed or high-torque machining
*Maximum T.I.R. is 0.0001"
*Each holder is lab certified for accuracy and comes with an individual lab report
*Tool holders are balanced at 25,000 to G2.5 tolerance
*Each holder comes with a coolant-thru set screw installed
Shipping Info:
*Actual Weight - .2125
CAT40 7/16"-3" - Shrink Fit Holder
Item #: TE1229025
Manufacturer: Techniks
Mfg #: 29025
Technical Specifications:
*Bore Diameter: 7/16
*Brand Name: Techniks
*European-DIN Tool Shank Range: 11.1mm
*Gage Length: 3
*Outside Diameter: 2.5
*Shank: 7/16
*Standard: ISO 1940
*Type: Shrink Fit CAT Holder
*USA-ANSI Tool Shank Range: 7/16
Description:
*ShrinkFIT tooling improves cutting tool life, cutting ability, and surface finish
*ShrinkFIT produces less wear and tear on the spindle bearings
*Ideal for high-speed or high-torque machining
*Maximum T.I.R. is 0.0001"
*Each holder is lab certified for accuracy and comes with an individual lab report
*Tool holders are balanced at 25,000 to G2.5 tolerance
*Each holder comes with a coolant-thru set screw installed
Shipping Info:
*Actual Weight - .1687
5/8-3/8X6.30"GL SHRINK EXTENSION
Item #: HA717758Z238Z
Manufacturer: Haimer USA LLC
Mfg #: 77.5/8Z2.3
Technical Specifications:
*Brand Name: Haimer USA LLC
Description:
Shipping Info:
*Actual Weight - .5500
CAT40 1"-4" - Shrink Fit Holder
Item #: TE1229042
Manufacturer: Techniks
Mfg #: 29042
Technical Specifications:
*Bore Diameter: 1.0
*Brand Name: Techniks
*European-DIN Tool Shank Range: 25.4mm
*Gage Length: 4
*Outside Diameter: 2.5
*Shank: 1.0
*Standard: ISO 1940
*Type: Shrink Fit CAT Holder
*USA-ANSI Tool Shank Range: 1.0
Description:
*ShrinkFIT tooling improves cutting tool life, cutting ability, and surface finish
*ShrinkFIT produces less wear and tear on the spindle bearings
*Ideal for high-speed or high-torque machining
*Maximum T.I.R. is 0.0001"
*Each holder is lab certified for accuracy and comes with an individual lab report
*Tool holders are balanced at 25,000 to G2.5 tolerance
*Each holder comes with a coolant-thru set screw installed
Shipping Info:
*Actual Weight - .2756
5/8-1/4X6.30"GL SHRINK EXTENSION
Item #: HA717758Z214Z
Manufacturer: Haimer USA LLC
Mfg #: 77.5/8Z2.1
Technical Specifications:
*Brand Name: Haimer USA LLC
Description:
Shipping Info:
*Actual Weight - .5500
BT40 1" x 90mm - Shrink Fit Holder
Item #: TE1239117
Manufacturer: Techniks
Mfg #: 39117
Technical Specifications:
*Bore Diameter: 1
*Brand Name: Techniks
*European-DIN Tool Shank Range: 25.4mm
*Gage Length: 3.54
*Outside Diameter: 2.48
*Shank: 1
*Standard: ISO 1940
*Type: Shrink Fit BT Holder
*USA-ANSI Tool Shank Range: 1
Description:
*ShrinkFIT tooling improves cutting tool life, cutting ability, and surface finish
*ShrinkFIT produces less wear and tear on the spindle bearings
*Ideal for high-speed or high-torque machining
*Maximum T.I.R. is 0.0001"
*Each holder is lab certified for accuracy and comes with an individual lab report
*Tool holders are balanced at 25,000 to G2.5 tolerance
*Each holder comes with a coolant-thru set screw installed
Shipping Info:
*Actual Weight - .2343
BT40 1/2" x 90mm - Shrink Fit Holder
Item #: TE1239114
Manufacturer: Techniks
Mfg #: 39114
Technical Specifications:
*Bore Diameter: 1/2
*Brand Name: Techniks
*European-DIN Tool Shank Range: 12.7mm
*Gage Length: 3.54
*Outside Diameter: 2.48
*Shank: 1/2
*Standard: ISO 1940
*Type: Shrink Fit BT Holder
*USA-ANSI Tool Shank Range: 1/2
Description:
*ShrinkFIT tooling improves cutting tool life, cutting ability, and surface finish
*ShrinkFIT produces less wear and tear on the spindle bearings
*Ideal for high-speed or high-torque machining
*Maximum T.I.R. is 0.0001"
*Each holder is lab certified for accuracy and comes with an individual lab report
*Tool holders are balanced at 25,000 to G2.5 tolerance
*Each holder comes with a coolant-thru set screw installed
Shipping Info:
*Actual Weight - .0993
BT40 3/16" x 90mm - Shrink Fit Holder
Item #: TE1239110
Manufacturer: Techniks
Mfg #: 39110
Technical Specifications:
*Bore Diameter: 3/16
*Brand Name: Techniks
*European-DIN Tool Shank Range: 4.8mm
*Gage Length: 3.54
*Outside Diameter: 2.48
*Shank: 3/16
*Standard: ISO 1940
*Type: Shrink Fit BT Holder
*USA-ANSI Tool Shank Range: 3/16
Description:
*ShrinkFIT tooling improves cutting tool life, cutting ability, and surface finish
*ShrinkFIT produces less wear and tear on the spindle bearings
*Ideal for high-speed or high-torque machining
*Maximum T.I.R. is 0.0001"
*Each holder is lab certified for accuracy and comes with an individual lab report
*Tool holders are balanced at 25,000 to G2.5 tolerance
*Each holder comes with a coolant-thru set screw installed
Shipping Info:
*Actual Weight - .0893